Enterasys Switches Crash Course

[ Login & Password ]

If admin / siemens doesn't work, try admin/none
default, no pwd, just enter
user : admin, rw, ro

C2(SU)-> set system login 'username' {super-user|read-write|read-only}{enale|disable}

C2(SU)-> clear system login 'username'
C2(SU)-> show system login

for rw and ro = set password
for admin = set system login

C2(SU)-> set password rw
C2(SU)-> set system password length 7

[ Assign IP address ]

C2(SU)-> set ip address x.x.x.x mask x.x.x.x gateway x.x.x.x
C2(SU)-> clear ip address

[ Webview ]

Default : enable
C2(SU)-> show webview : to see status of webview (default enable)
C2(SU)-> set webview enable : to enable webview
- login : http://172.16.2.10
C2(SU)-> show webview
WebView is Enabled

[ Set time ]

C2(SU)-> set time 7:50:00
C2(SU)-> set summertime enable

[ Set prompt ]

C2(SU)-> set prompt "switch 1"

[ Set system contact ]

C2(SU)-> set system name "Enterasys-C2.1"
C2(SU)-> set system location "Main Bldg 2nd Floor"
C2(SU)-> set system contact "ipBalance Admin (            888-999-0000      )Mr.admin@ipBalance.com This e-mail address is being protected from spambots. You need JavaScript enabled to view it "

[ Save configuration ]

C2(SU)-> save config

[ Configure ]

C2(SU)-> configure configs/Jan1_2004.cfg

[ Set command ]

C2(SU)-> set switch description 1 : describe switch name or location
C2(SU)-> set ip address {x.x.x.x} mask {255.255.255.0} gateway {x.x.x.x}
C2(SU)-> clear ip address
C2(SU)-> set time [mm/dd/yyyy][hh:mm:ss]
C2(SU)-> set logout 10 : closing session idle in 10 min
C2(SU)-> set port [enable|diable]
C2(SU)-> set port duplex
C2(SU)-> set cdp state disable fe.1.2
C2(SU)-> set cdp state disable fe.1.3
C2(SU)-> set vlan create 2
C2(SU)-> set vlan create 3
C2(SU)-> set vlan name 1 Management
C2(SU)-> set vlan egress 1 fe.1.1 tagged
C2(SU)-> set vlan egress 1 fe.1.22 untagged
C2(SU)-> set vlan egress 2 fe.1.1 tagged
C2(SU)-> set vlan egress 2 fe.1.2-14 untagged
C2(SU)-> set port alias fe.1.1 'To Computer room N1.1 Port 2'
C2(SU)-> set port vlan fe.1.14 2

[ show ]

C2(SU)-> show config port
C2(SU)-> show switch
C2(SU)-> show switch status 1
C2(SU)-> show system
C2(SU)-> show system hardware : to get serial#, MAC, Firmware version etc
C2(SU)-> show system utilization {cpu|storage}
C2(SU)-> show time
C2(SU)-> show console
C2(SU)-> show telnet
C2(SU)-> show system login : user login account info
C2(SU)-> show system lockout
C2(SU)-> show ip address
C2(SU)-> show ip protocol : shown "system IP address acquisition method: dhcp
C2(SU)-> show config port
C2(SU)-> show cdp
C2(SU)-> show port fe.1.14 (ex, show port *.*.*)
C2(SU)-> show port status fe.1.14 : shown on status of information for fe.1.14
C2(SU)-> show port counters fe.1.14
C2(SU)-> show port negotiation fe.1.14
C2(SU)-> show port broadcast fe.1.14
C2(SU)-> show spantree stats
C2(SU)-> show boot system

[ Lag ]

C2(SU)-> show lacp lag 0.1
C2(SU)-> set lacp enable
C2(SU)-> set lacp asyspri 1000
C2(SU)-> set lacp aadminkey lag.0.1 2000
C2(SU)-> set lacp static lag.0.6 fe.1.6
C2(SU)-> set lacp singleportlag enable
C2(SU)-> set port lacp fe.3.16 aadminkey 3555

[ Clear ]

C2(SU)-> clear config
C2(SU)-> clear vlan 3
C2(SU)-> clear vlan name 9
C2(SU)-> clear port vlan fe.1.3,fe.1.11
C2(SU)-> clear vlan egress 1 fe2.1
C2(SU)-> clear VNRAM

[ Reset ]

C2(SU)-> reset or reset 1 : reload switch 1

[ Configuration example ]

C2(SU)-> dir
C2(SU)-> show configuration outfile configs/
C2(SU)-> copy configs/ tftp://192.168.77.101/
using notepad, modify config
C2(SU)-> copy tftp://192.168.77.101/jan11_2006.cfg configs/jan11_2006.cfg
C2(SU)-> dir
C2(SU)-> configure configs/  : unit will reboot onto the modified config file
C2(SU)-> configure configs/Jan11_2006.cfg  :  to execute the"jan11_2006.cfg" configurationn file
C2(SU)-> delete configs/jan11_2006.cfg
C2(SU)-> clear config all
C2(SU)-> clear NVRAM
C2(SU)-> show snmp persistmode manual : manual save config
C2(SU)-> save config

[ Login & Password ]

If admin / siemens doesn't work, try admin/none
default, no pwd, just enter
user : admin, rw, ro

A2(SU)-> set system login 'username' {super-user|read-write|read-only}{enale|disable}
A2(SU)-> clear system login 'username'
A2(SU)-> show system login
for rw and ro = set password
for admin = set system login
A2(SU)-> set password rw
A2(SU)-> set system password length 7

[ Assign IP address ]

A2(SU)-> set ip address x.x.x.x mask x.x.x.x gateway x.x.x.x
A2(SU)-> clear ip address

[ Webview ]

Default : enable
A2(SU)-> show webview : to see status of webview (default enable)
A2(SU)-> set webview enable : to enable webview
- login : http://172.16.2.10
A2(SU)-> show webview
WebView is Enabled

[ Set time ]

A2(SU)-> set time 7:50:00
A2(SU)-> set summertime enable

[ Set prompt ]

A2(SU)-> set prompt "switch 1"
[ Set system contact ]
A2(SU)-> set system name "Enterasys-A2.1"
A2(SU)-> set system location "Main Bldg 2nd Floor"
A2(SU)-> set system contact "ipBalance Admin (            888-999-0000      ) Mr.admin@ipBalance.com "
 

[ Save configuration ]

A2(SU)-> save config

[ Configure ]

A2(SU)-> configure configs/Jan1_2004.cfg

[ Set command ]

A2(SU)-> set switch description 1 : describe switch name or location
A2(SU)-> set ip address {x.x.x.x} mask {255.255.255.0} gateway {x.x.x.x}
A2(SU)-> clear ip address
A2(SU)-> set time [mm/dd/yyyy][hh:mm:ss]
A2(SU)-> set logout 10 : closing session idle in 10 min
A2(SU)-> set port [enable|diable]
A2(SU)-> set port duplex
A2(SU)-> set cdp state disable fe.1.2
A2(SU)-> set cdp state disable fe.1.3
A2(SU)-> set vlan create 2
A2(SU)-> set vlan create 3
A2(SU)-> set vlan name 1 Management
A2(SU)-> set vlan egress 1 fe.1.1 tagged
A2(SU)-> set vlan egress 1 fe.1.22 untagged
A2(SU)-> set vlan egress 2 fe.1.1 tagged
A2(SU)-> set vlan egress 2 fe.1.2-14 untagged
A2(SU)-> set port alias fe.1.1 'To Computer room N1.1 Port 2'
A2(SU)-> set port vlan fe.1.14 2

[ show ]

A2(SU)-> show config port  :
A2(SU)-> show switch
A2(SU)-> show switch status 1
A2(SU)-> show system
A2(SU)-> show system hardware : to get serial#, MAC, Firmware version etc
A2(SU)-> show system utilization {cpu|storage}
A2(SU)-> show time
A2(SU)-> show console
A2(SU)-> show telnet
A2(SU)-> show system login : user login account info
A2(SU)-> show system lockout
A2(SU)-> show ip address
A2(SU)-> show ip protocol : shown "system IP address acquisition method: dhcp
A2(SU)-> show config port
A2(SU)-> show cdp
A2(SU)-> show port fe.1.14 (ex, show port *.*.*)
A2(SU)-> show port status fe.1.14 : shown on status of information for fe.1.14
A2(SU)-> show port counters fe.1.14
A2(SU)-> show port negotiation fe.1.14
A2(SU)-> show port broadcast fe.1.14
A2(SU)-> show spantree stats
A2(SU)-> show boot system

[ Lag ]
A2(SU)-> show lacp lag 0.1

A2(SU)-> set lacp enable
A2(SU)-> set lacp asyspri 1000
A2(SU)-> set lacp aadminkey lag.0.1 2000
A2(SU)-> set lacp static lag.0.6 fe.1.6
A2(SU)-> set lacp singleportlag enable
A2(SU)-> set port lacp fe.3.16 aadminkey 3555

[ Clear ]

A2(SU)-> clear config
A2(SU)-> clear vlan 3
A2(SU)-> clear vlan name 9
A2(SU)-> clear port vlan fe.1.3,fe.1.11
A2(SU)-> clear vlan egress 1 fe2.1
A2(SU)-> clear VNRAM

[ Reset ]

A2(SU)-> reset or reset 1 : reload switch 1

[ Configuration example ]

A2(SU)-> dir
A2(SU)-> show configuration outfile configs/
A2(SU)-> copy configs/ tftp://192.168.77.101/
using notepad, modify config
A2(SU)-> copy tftp://192.168.77.101/jan11_2006.cfg configs/jan11_2006.cfg
A2(SU)-> dir
A2(SU)-> configure configs/  : unit will reboot onto the modified config file
A2(SU)-> configure configs/Jan11_2006.cfg  :  to execute the"jan11_2006.cfg" configurationn file
A2(SU)-> delete configs/jan11_2006.cfg
A2(SU)-> clear config all
A2(SU)-> clear NVRAM
A2(SU)-> show snmp persistmode manual : manual save config
A2(SU)-> save config

[ Default Login & Password ]

Here is default  login passwords of the most Enterasys Switches.
A-Series, B-Series and C-Series Enterasys Switches.
User : admin
Password : [empty]
Try below commends to see current login

Enterasys_A2(SU)-> show system login

Password history size: 0 
Password aging        : disabled  

Username     Access           State  
admin          super-user      enabled 
ro               read-Only       enabled 
rw              read-write       enabled

To add user 'Chris' as a super-user

  Enterasys_A2(SU)-> set system login chris super-user enable
  Enterasys_A2(SU)-> show system login

Password history size: 0
Password aging        : disabled
Username     Access           State
admin       super-user          enabled
ro            read-Only           enabled
rw           read-write           enabled
chris         super-user           enabled

To delete user 'chris' from list

  Enterasys_A2(SU)-> clear system login chris

If you want to change password length 7

  Enterasys_A2(SU)-> set system password length 7

[ Syslog Server ]

While I was testing Splunk, I need to add more devices to Splunk index pages. This example shows how to configure Enterasys Switch to forward syslog message to the server. It's simple and easy to setup.

In this example, server's IP is 192.168.77.13 and UDP port 514 is used. Severity level is 8.

  Enterasys(su)>set logging server 1 ip-addr 192.168.77.12 port 514 severity 8 state enable

To verify

 

  Enterasys(su)>show logging server

IP Address    Facility   Severity      Description  Port  Status 
--------------------------------------------------------------- 1 192.168.77.12    local4    debugging(8)     default     514   enable

If you want to change default value to facility local 5 and severity 5, configure below.

Enterasys(su)>set logging default facility local 5 severity 5

To see currently logging severity levels for all applications on your devices, type below commands

Enterasys(su)>show logging application all

        Application   Current Severity Level
---------------------------------------------
89      CLIWEB                   6
90      SNMP                     6
91      STP                      6
92      Driver                   6
93      System                   6
94      Stacking                 6
112     UPN                      6
118     Router                   6
1(emergencies)  2(alerts)       3(critical)
4(errors)       5(warnings)     6(notifications)
7(information)  8(debugging)

[ Port Mirroring ]

source port 1/13
destinaion port 1/10

Console(Config)#interface Ethernet 1/1
Console(Config-if)#port monitor Ethernet 1/4
Console(Config-if)#

[ Upgrade Firmware ]

As you know Enterasys was named Cabletron company long long time ago. I guess more than decade Cabletron was one of strong vendor on switches market at that time. Due to I had really good experience with Cabletron product, I trust Enterasys's product line. Actually, I installed many Enterasys switches since 2005. Today, I just want to share a tip to upgrade firmware on Enterasys switches. Compare to generic 3rd party switch vendors, Enterasys release new firmware more often. Well, some of people might say due to all lot of bugs, but I like to say "Diligent and effort" (too much?).There are detailed documents from vendor, but this guide would be easier for beginner. Well, lets see what the steps to complete upgrading firmware are.
1. Find out what model of switch you are upgrading and what is current version of firmware running on the switch. Type "Show version" from the prompt.

- Model : C3G124-48
- Firmware : 01.01.02.0007

2. Go to the website "www.enterasys.com" and download proper firmware from the download library. and extract firmware to any folder your tftp server will use.

3. Assign IP address on the Enterasys switch in order to communicate with you computer which is running tftp server.
ex) computer 192.168.1.47, Enterasys switch is 192.168.1.8, default gateway .254

"set ip address 192.168.1.8 mask 255.255.255.0 gateway 192.168.1.254"

4. Ping the Enterasys switch from your computer.

5. Execute tftp server. (If you don't have, just down one from solarwinds)

6. Copy firmware from tftp server

Enterasys(su)->copy tftp://192.168.1.47/c3-series_01.02.04.0005 system:image

- I will take time...to be done (few minutes)

7. From the switch, make sure new firmware is uploaded and check which firmware version is on active.

8. Type to "set boot system c3-series_01.02.04.0005" to booting up switch with new firmware(active).

B2(su)>>set boot system c3-series_01.02.04.0005
Do you want to replace ? (y/n) y

Automatically Enterasys switch will reboot.

9. Confirm now, new firmware is on active status.

Taken From: http://www.ipbalance.com/vendor/enterasys/473-enterasys-stackable-c2-switch-tips-and-commands.html

The complete CLI reference manuals can be found at:

Enterasys C2 (Configuration Guide) : http://www.penteknoloji.com.tr/destek/c2/1.pdf
Enterasys C3 (Configuration Guide): http://www.penteknoloji.com.tr/destek/c3/2.pdf